Maintaining Yorkstone Slabs in a Solicitors Office

The pictures below are from a York Stone flagged hallway floor in an old building in the historic and picturesque market town of Newark, Nottinghamshire. The building dates back to the late 17th Century so the flagstone were likely to be very old, additionally the building is now the busy offices of local solicitor and so does get a lot of wear. The flagstones had a heavy build-up of soiling and old worn down coatings, there was also evidence of remove paint spots and I suspect adhesive residues suggesting at some point the floor had been covered in a carpet.

York Stone Flagstone Hallway Floor Before Cleaning in Newark

Cleaning Old Flagstones

The first step was to remove any previous coating such as sealers so a strong dilution of Tile Doctor Pro-Clean was applied and left to soak into the stone for twenty minutes. Pro-Clean is a multi-purpose heavy duty cleaner & coating remover that due to its alkaline formula is safe to use of Tile, Stone and Grout. The cleaning solution was scrubbed by hand into the wall edges and corners and paint spots and adhesive contamination marks were spot treated whilst the solution on the main part of the floor was getting to work breaking down the years of soiling. Once the edges were done it was time to agitate the flagstones on the main part of the floor with a weighted low-speed rotary machine fitted with a special restoration brush.

After thoroughly scrubbing the floor, the resulting slurry was vacuumed away and stubborn areas re-treated. The floor was then given a further rinse and the floor then left to dry off overnight.

Sealing York Stone Flags

The following day I returned to seal the floor. As the property dates back to the 17th Century it’s unlikely the floor has a damp proof membrane installed so it would be important to choose a breathable sealer that will allow moisture to pass up through the stone. We chose Tile Doctor Colour Grow for the job, it’s a breathable impregnating sealer that occupies the pores in the stone preventing contaminates from staining the floor and also enhance the natural colours in the stone. The flagstones were quite porous so three coats were required to ensure complete protection.

York Stone Flagstone Hallway Floor After Cleaning in Newark York Stone Flagstone Hallway Floor After Cleaning in Newark

I think you will agree from the photographs that flagstones have been transformed and the Colour Grow sealer will provide a durable barrier to both water & oil based spills. Tracked in soiling is also easier to remove when damp mop cleaning for which I recommended the use of Tile Doctor Neutral Cleaner which unlike acidic cleaners will not impair the integrity of the sealer.
 
 
Source: Tile, Stone and Grout Renovation in Nottinghamshire

Regular Maintenance of Restaurant Tiles

I was asked by my local Indian restaurant in South Croydon if I could improve the look of their marble tiles in the reception area of the restaurant. They had been laid several years ago and now the sealer was failing and dirt was becoming ingrained in the tile and especially the grout which had gone dark.

Marble Tiles Indian Restaurant South Croydon Before Marble Tiles Indian Restaurant South Croydon Before

Marble Tile and Grout Cleaning

To get the grout clean and remove the surface dirt we started with the application of a coarse grade diamond encrusted burnishing pad, the pad is used in conjunction with a little water which helps lubricate the process and it effectively cuts back the layer of grime from the surface. Rotary pads do struggle to reach into the grout lines so a medium dilution of Tile Doctor Pro-Clean which is a heavy duty tile and grout cleaner that’s safe to use on natural stone and grout was also scrubbed into the grout by hand using a stiff brush.

Marble Tiles Indian Restaurant South Croydon During Cleaning Marble Tiles Indian Restaurant South Croydon During Cleaning

The floor was then rinsed to remove the now dirty water and cleaning solution and we moved on to polishing the floor using a medium grade, fine and then super fine pads to build the surface shine backup. The floor was rinsed with water in-between each pad and then dried out as thoroughly as possible using large air movers.

Sealing Marble Floor Tiles

Normally I would have finished off with the application of Tile Doctor Shine Powder to give it a mirror like finish but the owner was happy with the way it looked and so once the floor had dried we moved onto sealing it with two coats of Tile Doctor Colour Grow which is an impregnating sealer that works from the inside by occupying the pores within the stone, it also enhance the colours within natural stone.

Marble Tiles Indian Restaurant South Croydon After Cleaning Marble Tiles Indian Restaurant South Croydon After Cleaning

The owner was over the moon with the results and has now engaged us to maintain the floor on a regular basis.

Marble Tiles Indian Restaurant South Croydon Before and After Marble Tiles Indian Restaurant South Croydon Before and After

 
 
Source: Tile, Stone and Grout Maintenance services in East-Surrey

Granite Floor Builders Clean

Granite is as you would imagine a very hard surface that looks beautiful when polished; in this case however it the floor had been abused by workmen who had been working at this commercial premises in the market town of Fareham and trailed all sorts of building materials and dirt onto the floor during renovation work. The once beautiful Granite floor tiles were now looking in a sorry state and the site manager was keen to have them restored to their former glory.

Polished Granite Floor Before Cleaning Fareham

Cleaning Marble Floor Tiles

The floor a quick sweep and wash down with a dilution of Tile Doctor Pro-Clean partly to ensure any surface grit etc. was removed but also so we could get a stiff grout brush in along the grout lines and give them a clean. Next the floor was rinsed down with water which was removed with a wet vacuum. The next step was to burnish the Granite with a set of four diamond encrusted burnishing pads which come in different grits and are applied in sequence working from coarse which removes old sealers and dirt through to medium, fine and super fine pads which build up the polish on the floor. The floor needs a rinse with water in-between each pad to remove any slurry and water is extracted from the floor using the wet vacuum, after the super fine pad we removed as much water from the floor as possible and left it to dry overnight ready for sealing the next day.

Sealing Marble Floor Tiles

Being a commercial floor I was concerned about the foot traffic wearing down the polish on the tiles so Tile Doctor Shine Powder was sprinkled onto the Granite and ground in using a little water to help lubricate the process and another pad at slow speed. Once this was complete the floor was buffed using a white buffing pad and now it looks transformed.

Polished Granite Floor After Cleaning and Polishing Fareham

 
 
Source: Tile, Stone and Grout Maintenance Service in Hampshire

Restoring Office Quarry Tiles

A company based in the 17th century market town of Watlington were renovating their office space and decided to replace the carpet which had been glued to the floor below. Upon further inspection this turned out to be a Quarry Tiled Floor and they were keen to restore it and so we got the call.

Quarry Tiles Before Cleaning in Watlington

Restoring Quarry Tiles

I first covered the whole floor with Tile Doctor Remove and Go, leaving this to dwell for a while whilst I fitted a scrubbing pad to my rotary machine. Once the machine was ready the whole floor was scrubbed followed by a rinse with water; the resultant soil was then extracted from the floor using a wet vacuum. This process removed most of the glue so I repeated the process until satisfied all the glue had gone. Remove and Go lives up to its name and although normally used to remove sealers it will remove most other coatings as well. This process took up most of the day so after the final and thorough rinse I left the floor to dry aiming to come back the next day to seal it.

When I returned the next day the floor had white patches of effervescence on it where salts had been forced up through the tile as the water evaporated; this had to be dealt with before the tiles could be sealed so I spent the second day scrubbing the entire floor with Grout Clean Up to remove it, after finishing the floor was given another thorough rinse to remove any product from the floor and used the wet vacuum again to get it as dry as possible.

Sealing a Quarry Tiled floor

I returned the third day to a nice dry and most importantly clean floor. To seal Quarry tiles I usually go for Tile Doctor Seal and Go as it’s water based (so no smell) and it adds a nice shine to the floor; however in this case being an office environment with a lot of heavy traffic I decided to go with Tile Doctor Colour Grow which is an impregnating sealer that soaks into the pores of the tile and is likely to be more durable, it also enhances the natural colours in the tile leading to a very nice finish.

Quarry Tiles After Cleaning in Watlington

I think you will agree the final result was a remarkable transformation
 
 
Source: Office Tiled Floor Restoration in Oxfordshire

Slate Floor Restored at new Yoga Studio

This Slate tiled floor is in a barn in Beckley, near Rye, Hawkhurst, Tenterden and Robertsbridge. For years it had been used to store furniture, gardening equipment and worryingly, a leaky motorbike which had stained the slate.

Slate Floor in Beckley Barn Before Oil Staining
You can see from the photographs below that the Slate tiles were much worn, stained, faded and far from looking their best.

Slate Floor in Beckley Barn Before Slate Floor in Beckley Barn Before

Deep Cleaning Slate Tiled Floor

Firstly I swept out the whole area then applied Tile Doctor Remove and Go to several areas where engine oil had leaked. After leaving it to soak in for fifteen minutes I began to strip and clean the floor with Tile Doctor Pro-clean worked in with a buffer machine fitted with a black scrubbing pad. However it became apparent that some of the ridges on the slate were damaging the black pad so the remainder had to be done by hand with a deck brush. Once the stone was stripped and cleaned the appearance was even greyer than before. I assured the customer that once the sealer has been applied it would be transformed to a much darker colour.

Sealing Black Slate Floor Tiles

After two days drying I returned to seal the floor checking first to ensure it was dry and no further work was required which is just as well as I had to wipe away what appeared to be stray dog paw prints. I got to work applying Tile Doctor Ultra Seal having previously estimated that four coats would sufficient to give it a dark finish; I should mention that Ultra Seal was chosen due to the fact that it’s provides a no-sheen natural look appearance.

Frustratingly it was quite a cold barn with little ventilation despite it being an unseasonably warm autumn day outside and this increased drying times. However by about four o’clock in the afternoon the job was finished and looking remarkably transformed. The customer was pleased with the improvement and is now moving forward with to fit out the barn as a yoga studio.

Slate Floor in Beckley Barn After Slate Floor in Beckley Barn After

Source: Tile, Stone and Grout Cleaning in Sussex

Reducing Coefficient of Friction

We recently had a request to take a look at the Ceramic floor tiles installed at a fairly new office building in Lancaster. Well over 300 people work at the builder and they all come and go via the entrance hall where ceramic tiles have been installed which when wet were very slippery. To confirm this we conducted a pendulum test which is a specially designed piece of certified equipment that measures the surface co-efficient of friction which basically is a recognised measure of how much traction a surface has. The testing is very detailed and the output is an official report that can be used for insurance purposes; the report came back high risk which was expected so no surprise there, the next step was to see how this could be improved.

Applying Anti-Slip Treatment to Ceramic tiles in Lancaster Before

Cleaning Porcelain Tiles ready for Anti-Slip treatment

As well as maintaining Tile and Stone Tile Doctor are also trained in the application of Anti-Slip treatments so we were asked to apply Anti-Slip to the 36m2 of Ceramic tiles in the entrance and rectify the problem. We do this by first getting the floor as clean as possible for which we use a dilution of Tile Doctor Pro-Clean worked into the floor with a rotary machine fitted with a scrubbing pad. The dirty cleaning solution is removed using a wet vacuum and the floor rinsed with clean water.

Applying Anti-Slip treatment to Porcelain tiles

The second step is to apply a Priming and Locking solution which is part of the treatment diluted one part solution to four parts water. This is then left to dry and once dry is followed by the application of the Anti-Slip treatment itself.

The third step in the treatment is to re-apply the diluted Priming and Locking solution before the floor fully dries out and it’s this last step that activates the treatment and locks it in place. There’s no need to wait for the floor to dry at this point it can be used immediately after the last step has been applied.

Applying Anti-Slip Treatment to Ceramic tiles in Lancaster During

Once completed we conducted another Pendulum test so this could be compare to the original test to see if there had been any improvement. I’m glad to report the treatment worked as expected and the latest report came back as low risk. The customer keeps this to prove to any potential insurance claimant that steps had been taken to make the floor as safe as possible. You might notice that floor looks much better as well.

Applying Anti-Slip Treatment to Ceramic tiles in Lancaster After

I should mention that the work was carried out outside of working hours so no disruption was made to the normal operation of the building.
 
 
Source: Tile and Stone Anti-Slip Treatments in Lancashire

Cleaning and Sealing 120m2 of Slate Tiles at an Enterprise Centre

These photographs are taken at an Enterprise Centre in Millom where local business are encouraged to network and they also offer various training courses, all of which results in a large amount of people coming and going across the 120m2 of rough black Slate which covers the communal areas. Interestingly enough this is not the first time we have cleaned and sealed this floor with the last visit being five years ago. Five years of wear and tear had taken its toll on the tiles though and the black Slate was looking tired but not horrendous given its location so I think it’s fair to say the sealer had performed well over the Intermitting period.

Rough Black Slate Millom Before Cleaning

Cleaning Rough Black Slate

As I mentioned before the area in total was about 120m2 which is a large area so we operated in sections working around the public and ensuring the correct signage was displayed were relevant.

To clean the Slate tile and grout and remove the remaining sealer the floor a good deep clean using a dilution of Tile Doctor Remove and Go leaving it to soak in for fifteen minutes before working it in with a black scrubbing pad fitted to a rotary buffing machine. This process was followed by rinsing and cleaning with fresh water, stubborn areas were retreated and the water was removed using a wet vacuum to the get the floor as dry as possible.

Sealing Rough Black Slate

Once the section of floor was clean we left it to dry and moved onto cleaning the next section coming back later to seal it which we did with two coats of Tile Doctor Colour Grow which is an impregnating sealer that occupies the pores preventing contaminates from becoming ingrained. Colour Grow is also a colour enhancing sealer that brings out the deep colour in the slate.

Rough Black Slate Millom After Cleaning

The customer knew about using the right cleaning solution for regular cleaning however as it had been five years since our last visit we thought it best to remind them and recommend the use of Tile Doctor Neutral Cleaner which will not reduce the life of the sealer like an acidic cleaning product would.
 
 
Source: Commercial Tile and Stone Cleaning and Sealing in Lancashire

Applying Anti-Slip to a Golf Course Changing Rooms

I recently paid a visit to a Golf Club in Derbyshire to assist local Tile Doctor Steve Carpenter with the application of Anti-Slip treatment to the 6inch porcelain tiles in the men’s changing rooms. This is the advantage of being a member of a large network, if a fellow member needs assistance on a time consuming job they can just ask for assistance. In this case the floor was only around 12m2 but the Golf Club were hosting a Tournament later that afternoon and needed the work completing before 1pm.

Anti-Slip Preparation Derbyshire Golf Course

Cleaning Porcelain Tiles ready for Anti-Slip treatment

For best results the Anti-Slip treatment requires a clean surface so the first job was to give the tiles a thorough wash using Tile Doctor Pro-Clean worked into the floor with a rotary machine fitted with a scrubbing pad. The resultant dirty cleaning solution was then removed using a wet vacuum and the floor rinsed with clean water.

Applying Anti-Slip treatment to Porcelain tiles

The next step was to apply the Priming and Locking solution to the tile surface diluted one part solution to four parts water and this was left to dry. Once dry we applied the Anti-Slip treatment ensuring the tile was kept wet for up to 20 minutes in the process. The last step in the treatment was to re-apply the diluted Priming and Locking solution before the floor fully dried, it’s this last step that activates the treatment and locks it in place. There’s no need to wait for the floor to dry at this point it can be used immediately after the last step has been applied.

Anti-Slip Treatment Derbyshire Golf Course

To test the floor I invited the manager to try the floor dry and wet so he could experience the improvement in surface friction on a wet surface for himself. The treatment worked well and the manager was impressed, not only that we managed to complete the job with 45 minutes to spare.

For after care we recommend the floor should be cleaned daily by damp mopping with our Neutral Tile Cleaner, diluted at 35ml per 5-Litres of water periodically scrubbing the floor with a deck brush.
 
 
Source: Residential and Commercial Tile, Stone and Grout Cleaning in Lancashire

Victorian Hallway at Grade 2 Listed Salford Town Hall Remodelling

This original Victorian Tiled floor was uncovered at the Grade 2 listed Salford Town Hall in Salford, Manchester. This public building which built around 1827 was the former Salford Town Hall and Magistrates Court; it’s currently being turned in to luxury apartments and this amazing floor is located in the main entrance hall. The floor was only recently re-discovered during the conversion works after being hidden for many years and was in surprisingly good condition. The company remodelling the building are maintaining the historic features so we got the call to go in and clean and seal the floor.

Victorian Tiles at Salford Town hall before

Cleaning Victorian Tiles

Cleaning the floor was fairly straight forward and involved the application of a dilution of Tile Doctor Pro-Clean which was left to dwell on the tile for around ten minutes before being worked into the Tile and Grout using a rotary machine fitted with a black pad. The dirty solution was removed using a wet vacuum and the whole floor rinsed down three times to ensure there was no trace of cleaner left on the floor. It’s a large tiled area so it took the whole day to complete.

Sealing Victorian Tiles

I returned the next day to see that the floor had dried off overnight and so started to seal it using Tile Doctor Seal & Go which is a topical sealer that adds a nice shine to the tiles, five coats of sealer were needed before the tiles were fully sealed. I think you would agree the floor now looks fantastic; certainly the client was happy with the finish.

Victorian Tiles at Salford Town hall after

 
 
Source: Commercial Tile, Stone and Grout Cleaning in Greater Manchester

Cleaning Travertine tiles at a University

This rather dirty Travertine tiled floor is located in the reception area of the hotel and conference centre of the Cranfield University, apparently the tiles had been laid ten years prior and had not been properly cleaned and resealed since.

Cleaning Tumbled Travertine Tiles

Before starting we covered all the area around the floor with masking tape and plastic sheeting to protect it from any splashing which can happen when you’re using high speed floor machines.

The tiles were in need of a good deep clean so a strong dilution of Tile Doctor Pro-Clean was applied to the floor and left to soak into the tile for twenty minutes before being scrubbed in with a using a rotary machine fitted with a scrubbing pad. The soiled solution was rinsed off using clean water and extracted using a wet vacuum repeating the process until you could see the improvement in the floor. A stiff hand brush was also used along the grout lines with more Pro-Clean to get them clean.

Travertine Tiles Before Cleaning at Cranfield University Travertine Tiles After Cleaning at Cranfield University

Burnishing Travertine Tiles

To restore the shine back to the travertine we used a set of diamond encrusted burnishing pads starting with a coarse pad and a little water fitted to a heavy rotary machine, the coarse pad strips off any remaining dirt and seal from the floor, the resulting slurry was then removed using a wet vacuum.

Once finished with the course pad we moved on to the medium and fine pads again with a little water until the floor was polished. The final “Very Fine” pad brings up the polish on the floor and buffs it to a nice shine.

Sealing Travertine Tiles

Last step was to seal the tiles which would prevent any dirt getting trapped in the pores making it easy to clean and ensuring it keeps it appearance for longer. For this we used two coats of Tile Doctor Colour Grow which as well as sealing the tiles works to bring out the natural colours in the stone.

The customer was very happy with the results and commented that they thought the transformation was amazing.
 
 
Source: Commercial Travertine Tile Cleaning in Bedfordshire

Polishing a Terrazzo School floors

This Terrazzo Floor was at the entrance to a School in Kilmacolm where as you can see from the photograph below had come under some heavy use and was now proving difficult to keep clean. We were asked to give it a deep clean, polish and re-seal therefore making it much easier to maintain going forward.

School Terrazzo Floor Kilmacolm before cleaning

Cleaning a Slate Floor

Hard stone surfaces such as Terrazzo have to be burnished to get the shine back and this process basically involves cutting back the surface with a set of diamond encrusted burnishing pads.

Before burnishing however the floor was swept out to remove any loose debris that could get caught under the pads and scratch the floor. Once that was done a Coarse 400 grit burnishing pad was fitted to our heavy rotary machine and run over the surface with a little water to help lubricate the process, the coarse pad removes surface dirt and coatings such as sealers. Once that was finished we moved onto the medium 800 grit pad which is the first step of the polishing process and also removed ingrained dirt. The surface of the Terrazzo is still quite rough at this stage so once complete with the medium pad the fine (1,500 grit) is used smooth down the surface and continue to build up the polish in the floor. The last pad is a very fine (3,000 grit pad) and this pad builds on the existing polished effect to create a high shine finish.

All these pads are applied with water and the resultant slurry needs to be cleaned off during the process with the final step of giving the floor a thorough rinse with clean water, I can recommend a wet vacuum at this point as it makes light work of removing liquids from floors.

Sealing a Terrazzo Floor

Once the floor was completely dry it was sealed using two coats of Tile Doctor Colour Grow which is a great product to use of these characteristic floors as it brings out the colour in the floor as well as providing on-going stain protection. The floor was then buffed using a white buffing pad to bring up the shine further; needless to say our client was extremely happy with the finished result.

School Terrazzo Floor Kilmacolm after cleaning

 
 
Source: Commercial floor cleaning services in Glasgow

Cleaning Quarry Tiles in a Commercial Kitchen

This job was to strip and re-seal these Quarry tiles installed in a commercial kitchen which was undergoing refurbishment at a canteen in Rushden, Northamptonshire. The tile finish had dulled and there was a lot of staining to the grout.

Quarry Tiles in Rushden before cleaning

Cleaning Quarry Tiles

As there was little in the way of kitchen units to protect I go straight down to stripping down the floor using a strong dilution of Tile Doctor Pro-Clean which is a multi-purpose cleaner/stripper that’s safe to use on stone, tile and grout. The solution was applied with a mop and left it to dwell on the floor for twenty minutes in order to give it chance to soak into the tile surface and get to work on the existing sealer and dirt. It was then worked into the floor using a rotary machine fitted with a black scrubbing pad and stiff hand brushes were used along the grout lines to get the grout clean. The resulting soiled solution was picked up with a wet and dry vacuum and the floor was then rinsed with clean water to neutralise the tile and stubborn areas re-treated. Once I was happy the floor was given a final rinse and then left to dry overnight ready for sealing the next day.

Sealing Quarry Tiles

After checking the tiles had dried I proceeded to seal the floor using four coats of Tile Doctor Seal and Go which will protect the floor from staining going forward and also adds a nice shine to the tile.

Quarry Tiles in Rushden After cleaning

 
 
Source: Quarry Tile floor cleaning services in Northamptonshire

Cleaning a Vinyl floor at a Coventry church

The great thing about being in the floor cleaning business is that the equipment we use are very flexible and allow the cleaning of many surfaces from Tile, Stone, Grout and Carpet through to in this case a Vinyl floor at Church in Wyken.

Vinyl floor in Wyken before cleaning Vinyl floor in Wyken before cleaning

Cleaning Vinyl Flooring

You can see from the photograph that although the floor was in good physical condition it was dirty and in need of a really deep clean. To do this the floor was mechanically scrubbed using a rotary machine fitted with a scrubbing pad and a solution of Tile Doctor Pro-Clean which is a very flexible heavy duty cleaning product primarily designed for Tile, Stone and Grout but equally effective on Vinyl floors as well. The soiled cleaning solution was then washed away with water which was removed using a wet vacuum and left to dry.

Vinyl floor in Wyken during cleaning Vinyl floor in Wyken during cleaning

Sealing Vinyl

Once the floor was dry three coats of Tile Doctor Seal and Go were applied to the surface which restored the shine finish. You have to wait for a coat to dry before applying the next so this process can take a while to complete.

Vinyl floor in Wyken after cleaning Vinyl floor in Wyken after cleaning

 
 
Source: Commerical and Residential Vinyl floor cleaning services in Coventry

Stone Floor cleaning at Car Dealership Office

These photographs are from the cleaning of a Travertine tiled floor installed in an old house in Dunmow that had been used as offices by employees of a Ford dealership. The house was empty when we started the cleaning process and you could see that the dirt had become ingrained into the tile and any sealer that had been present had now been worn away.

Travertine Tiles in Dunmow Office Before Cleaning

Cleaning Travertine Tile and Grout

We tackled the grouting first by applying Tile Doctor Pro-Clean (diluted 1 part cleaner to 3 parts water) which was left to dwell on the grout for about fifteen minutes before being scrubbed in using small stiff hand brushes. As you imagine this was time consuming but the grout came up really well so the end result was well worth the effort. The tiles were then cleaned using more Pro-Clean (diluted 1 part cleaner to 2 parts water) but this time we were able to use a scrubbing machine fitted with black pads. We scrubbed the tiles several times in order to bring them up to a good standard. The floor was also washed down at this point to remove the soiled cleaning solution, all liquids being removed using a wet vacuum.

Travertine Tiles in Dunmow Office During Cleaning

Burnishing Travertine Tile

The Pro-Clean worked well to clean the Travertine but if you want to restore the original appearance it needs to be burnished using a set of diamond encrusted burnishing pads. The pads come in a set and you start with the coarse pad and a little water and move on through to the very fine pads until the surface is pristine.

To protect the floor and bring up the appearance even further Tile Doctor Shine Powder was polished into the floor using a buffing pad, the powder add a deep finish to the appearance of the travertine and hardens on the surface to provide durable surface protection.

Travertine Tiles in Dunmow Office After Cleaning

I think you will agree we have managed quite a transformation; certainly the customer was very happy with the work.
 
 
Source: Commercial Floor Cleaning Service in South Essex

Commerical Kitchen Floor Cleaning

The Quarry tiles shown below were installed in the kitchen of a take away restaurant near Hockliffe, as you can see they were quite tarnished and not looking their best due to general wear and tear and the use of strong cleaning products; an inspection was also due and the proprietor was concerned it would be an issue.

Cleaning Quarry Tiles at Hockliffe Takeaway Before

Cleaning Quarry Tiles

To clean the floor tile and grout I decided to apply a strong combination of Tile Doctor Pro-Clean mixed 50/50 with NanoTech Ultra Clean and then diluted with water. This combination creates a powerful cleaning product containing nano sized abrasive particles that can penetrate deep into the dirt. The cleaning solution was left to dwell on the surface of the tile for twenty minutes before scrubbing with a rotary machine fitted with a black scrubbing pad and then washed off with a Rotovac machine which applies and removes hot water at high pressure effectively cleaning the tile and grout and rinsing then removing the water at the same time.

Cleaning Quarry Tiles at Hockliffe Takeaway After

Sealing Quarry Tiles

Once we were happy with the Quarry tile and grout was clean we left the floor to dry assisted with air blowers to speed up the process. It wasn’t long before it had dried and we were then able to the Tile and Grout using Tile Doctor High Shine sealer which should protect the floor for at least three years given the high traffic, this is of course as long as they use the correct cleaning products as acidic products will reduce the life of a sealer. The kitchen was now ready for inspection where it should pass with flying colours.

Source: Cleaning Takeaway Kitchen Tiles Prior to Inspection in Bedfordshire

Commerical Grade Terrazzo Floor restored at Wigan Chip Shop

These photographs are of a Stained Terrazzo Tiled floor from an old Fish and Chip shop in Wigan which had been closed for several months due to the owner being ill. The shop had then been sold and the new owners asked us to call in and re-furbish the tired and badly stained tiles rather than go to the expense of re-tiling or re-surfacing the Floor area, which would have cost a lot more than what we charged.

Terrazzo Tile at Wigan Fish and Chip Shop Before Terrazzo Tile at Wigan Fish and Chip Shop Before

Terrazzo is a composite tile made up of Marble and Limestone chippings, sometime Granite, all mixed into a clear cement resin and then made up into tiles of all sizes. We estimated these tiles we laid more than fifty years prior and were not looking their best after being stained with rust stains from heavy equipment, cooking oil and grease, ingrained dirt and grime. Although a tough job to tackle it didn’t put us off and as you will see we still managed to get them clean again.

Cleaning Terrazzo Tile

The method we used to restore the surface was to cut them back using a set of burnishing pads which take off a few millimetres off the tile surface and regrinds to make them look as good as new, this is something you can’t do with Vinyl Tiles or Ceramic and Porcelain. The pads are encrusted with diamonds and are used in conjunction with a little water; you start with a coarse pad and work through the set of pads which become finer in grade as you progress until your polishing the surface. Once this process is complete the floor was given a good wash down to remove any soil and allow us to spot any areas that needed further attention.

Sealing Terrazzo Tile

When the Terrazzo tile was dry it was sealed sealing with two coats of Tile Doctor Colour Grow which is an impregnating matt sealer that brings out the colours in natural stone, the client had also specified they didn’t want a shiny finish as they had a concern about slippery surface that could lead to slips and falls. Once the sealer was dry it was buffed using a white buffing pad.

Terrazzo Tile at Wigan Fish and Chip Shop After Terrazzo Tile at Wigan Fish and Chip Shop After

The results are quite satisfying given the age of the floor and the stains we had to deal with not only that but the owner had engaged a number of other cleaning companies who had tried a test clean and he had even tried cleaning it himself but the results were poor.

Terrazzo Tile at Wigan Fish and Chip Shop Completed

 
 
Source: Commerical Tile and Stone Cleaning Services in Lancashire

Slippy Porcelain Tile Solutions

We were contacted by a builder who had recently laid Porcelain Tiles in an office reception in Wimbledon. Although he has laid this type of tile in various art galleries around London without problem, in this particular lobby which is situated next to a shopping centre the tiles were extremely slippery and the facilities manager wanted the tiles changed at the expense of the builder.

Antislip Application Porcelain Tile Wimbledon

Obviously this would have been an expensive option and so the builder contacted Tile Doctor for help. Initially he had considered having a member of his team apply the treatment however he realised that as a Tile Doctor applicator we had been trained to apply the treatment properly and this gave the facilities manager confidence it would have been applied to the correct standard so we were awarded the work and asked to carry it out on a Sunday when the building would be empty.

Antislip Application Porcelain Tile Wimbledon

Applying the Anti-Slip Treatment

We arrived at the agreed time and were let in by the shopping centre security team. The area we were treating was around 25m2 so decided to work in 5m2 sections first cleaning the tile using the first stage Ant Slip product worked into the tile with a rotary floor machine fitted with a polypropylene brush head and then removing with a wet vacuum followed by rinsing with clean water.

We carried on with this process until the whole floor was done and let it dry before going onto the next stage to apply the Tile Doctor Anti slip (stage two) and leaving for between 3 to 5 minutes before applying the stage three which locks in the Anti Slip.

Antislip Porcelain Tile Wimbledon

The Anti Slip product is invisible to the eye however it’s very easy to test it’s been applied, all you need to do is wet the tile as the product only activates when it’s wet.

Antislip Porcelain Tile Wimbledon

When we had finished the whole floor we then tested it again just to make sure that everything worked well we cleared away all the tools making sure we left the area tidy and safe and locked the building up.

The Job took us one night and the customer is now recommending us to all other sites that have had these tiles fitted.
 
 
Source: Porcelain Tile Cleaning Questions Answered

London Night Club Toilet Tile Cleaning

Our client’s project was to refurbish four toilets in a London Night Club but didn’t want the expense of replacing all the existing ceramic floor and wall tiles; after come across our web site we were invited to visit the club and provide a demonstration after which we were awarded the contract. Our main task on this project was to deep clean the ceramic wall tiles and floors and colour seal grout lines which had over the years had stained to a yellow appearance

Night Club Toilet Cleaning Day One

We started by giving all the tiles a though deep clean with Tile Doctor Pro-Clean which is a strong alkaline cleaner that is able to penetrate into the tile and lift the years of built up soiling on the tile and grout lines. This was followed with a further treatment of on the wall tile grout lines using Tile doctor Grout Clean up and another deep clean with Pro-Clean and pressure cleaned using our powerful truck mounted system which cleans under heat and high pressure and returns all the slurry to our recovery tanks for disposal.

Night Club Toilet Cleaning Day Two and Three

The tiles looked fantastic and like new again with the exception of the grout lines which although being deep cleaned of twenty years of dirt and grease still had a yellow appearance. The solution was to use a Grout Colourant to colour all the grout lines white again, the product we use is brilliant as not only does it give the appearance of newly applied grout is also protects the grout with a waterproof and stain proof barrier that is very easy to clean. Once dried we removed all the excess grout colourant residue from the tile and then polished the tiles to a pleasing high shine.

The client was totally satisfied and impressed with our work which cost a fraction of what it could of cost to replace all the wall tiles. In fact a member of the management team was adamant that we had replaced the tile and grout as he thought it impossible we could of managed this good as new look any other way.
 
 
Source: Contract Floor Cleaning Services in London

Coffee Shop Floor Cleaning Contract

The Ceramic tiles with dark grout were installed in a Bedford Coffee Shop where we have a regular contract to deep clean the tile and grout, whilst we appreciate the regular work you do have to work out of hours to minimise impact to trade. It’s worth noting that many commercial tiling installations do avoid white grout as it can get dirty quite quickly and will be difficult to clean if badly stained, not that that’s a problem for Tile Doctor as we have a solution for most problems.

Cleaning Ceramic Floor Tiles

This was a general maintenance clean so a dilution of Tile Doctor Pro-Clean was applied to the floor and left to soak in for 20 minutes or so before giving the floor a thorough clean using a Rotovac machine which applies and removes water at high pressure to remove the dirt and rinse the floor. Once this was done we took the opportunity to apply more Pro-Clean to the grout and hand scrubbed along the grout lines using a stiff brush to ensure the black grout was clean.

Ceramic Tiles Bedford Coffee Shop Before and after

Ceramic tiles don’t normally need a sealer so once all the tile and grout was clean and was dry we were done.
 
 
Source: Ceramic Coffee Shop Floor Tiles Cleaned in Bedford

Cleaning Etched Anti Slip Tiles

You may recall a Limestone job I did recently at a Manchester country club in Hale. This Anti-Slip porcelain floor was installed at the same location in the passageway on route to the toilets and in the toilets themselves. Slips and falls can be a huge problem for buildings with public areas and so tiles which have been etched to make a normally smooth surface rough make perfect sense, the downside of course is that those rough surfaces trap dirt and are difficult to clean. Tile Doctor have a chemical Anti-Slip alternative that only activates when the tile get wet that doesn’t require the tile to be etched but it does need to re-applied every few years.

Anti Slip Tiled Hallway Before Cleaning Anti Slip Tiled Hallway Before Cleaning

Cleaning Anti Slip Floor Tiles

The floor tiled need a deep clean to bring out the ingrained dirt so we applied a strong solution of Tile Doctor Pro-Clean using two parts water to one part Pro-Clean and left it to soak into the tile for twenty minutes. The solution was then scrubbed into the tile using a rotary machine fitted with a black scrubbing pad. You could see the dirt coming out the pores of the tile and the resultant soiled solution was removed using a wet vacuum before washing the tiles down with clean water.

Anti Slip Tiled Hallway After Cleaning Anti Slip Tiled Hallway After Cleaning

Including the ladies, gents and hallway there was a lot of floor area to cover and some of the stubborn areas had to be re-treated so it was a long job but I think you will agree the floor now looks great.
 
 
Source: Commercial Tile Cleaning Problems solved in Manchester