Resolving Water Stained Safety Flooring

Just for a change I thought I would post something a little difference from the usual stone floor projects I get involved in. The floor below at a building in Turville near Henley on Thames and is of an “Altro Safety floor” belonging to an existing customer of mine. This is a heavy duty type of flooring usually found in industrial/office premises and normally these floors require little maintenance but in this case however a small flood left the floor difficult to clean.

Altro Safety Floor Before Cleaning Turville

Deep Cleaning an Altro Safety Floor

To restore the floor back to its original condition I first pre wet the floor and applied Tile Doctor neutral cleaner to the floor and left it to dwell, I then scrubbed the floor with a coarse burnishing pad fitted to a rotary scrubbing machine, I then rinsed with water and extracted the dirty water with a wet vacuum then mopped the floor with more neutral cleaner.

Altro Safety Floor After Cleaning Turville

Being a safety floor there was no need to seal the floor but before leaving I worked out a maintenance plan for the customer that will enable them to keep the floor in good condition going forward.
 
 
Source: Commercial Floor Cleaning Services in Oxfordshire

Removing Limescale from Stone Bathroom Worktops at a Business Park

This job required the cleaning of Marble Worktops in twelve toilets at a very nice office in the Abingdon Science Park. The building was occupied by a company called Sophos who you may have heard of and over a period of time the Marble had become stained through the build-up of Limescale from the water supply and the cleaning company servicing the office could not clean it off. I’ve seen a few horror stories of stone surfaces being damaged through the use of acidic Limescale removers so the cleaning company was quite right not to touch it.

Marble Bathroom Worktop Abingdon Before

Polishing Marble Worktops

To remove the Limescale it would be necessary to hone the Marble using a set of small six inch burnishing pads fitted to a handheld buffing machine. The process involves starting with the coarse 400grit pad with a little water which cuts through the Limescale and then moving on to the 800, 1500 and finishing with 3000 grit to hone the surface and build the polish backup. The water helps lubricate the activity and the surface needs to be rinsed down between each pad.

Sealing Marble Worktops

When the surface was dry I applied two coats of Tile Doctor Colour Grow which is a colour enhancing sealer which impregnates the pores of the stone to protect it, it also enhances the natural colours in the stone.

There were twelve of these to do so as you can imagine it took me a while to get round.

Marble Bathroom Worktop Abingdon After

If you are experiencing a similar problem with highly polished Marble do get in touch as we can achieve a mirror finish.
 
 
Source: Commercial Tile, Stone and Grout maintenance service in Oxfordshire

Cleaning Concrete Works of Art

This was an unusual request to clean a modern piece of contemporary artwork by New York City artist Mel Kendrick on display in one of the gardens of the Wormsley Estate. I’m no art expert but having done some research on the internet it appears to be part of a collection known as “Markers” that were on display at the Madison Square Park in 2009. The work is made from concrete cast into different coloured sections and fitted together to form a rather larger piece of art which having been exposed to the UK elements was now starting to discolour and go orange in part.

Mel Kendrick Markers Modern Art Wormsley Before Cleaning

Cleaning Modern Concrete Artwork

Being such a prestigious work of art i had to be careful not to damage the stone in anyway so after careful consideration I worked out a process using an alkaline cleaning product Tile Doctor Pro-Clean.

Mel Kendrick Markers Modern Art Wormsley Before Cleaning Mel Kendrick Markers Modern Art Wormsley Before Cleaning

To get the statue clean I used a warm water dilution of Tile Doctor Pro Clean working it into small areas at a time spraying the solution on and scrubbing with a brush, then rinsing it off with clean water. This process took some time but certainly did the trick.

Sealing a Concrete Artwork

With this project being outdoors and with it taking a couple of days I had to pick a good weather window and fortunately the weather held out long enough so I could continue and seal the concrete in order to protect it going forward. Again careful consideration had to be given to the choice of sealer and in the end I went with Tile Doctor Ultra Seal which is an impregnating sealer that soaks into the pores protecting from within and most importantly it’s a natural look sealer that does not change or enhance the colours.

Mel Kendrick Markers Modern Art Wormsley After Cleaning

If you’re a lover a modern art then you should appreciate the difference and will agree with me that the statue now looks new again.

Source: Professional Tile, Stone and Grout maintenance service in Oxfordshire

Assisting Cleaning Companies To Resolve Tricky Problems

This call actually came from a cleaning company where one of their cleaners had been to a customer in the village of West Hanney near Wantage and tried to clean the walls of this Limestone Shower using a supermarket Limescale remover, which as you can see from the photograph below didn’t work out very well.

I should point out that Limescale removers contain some strong acids which should never be used on stone or sealed surfaces as the acid will etch the surface. Even weak acid cleaners used over time will have an effect so do take care and always read the label.

Damaged Limestone Shower Wall West Hanney Before

Resurfacing Limestone Shower Tiles

To restore the surface I realised it would need to be treated like a polished stone floor and burnished. So with this in mind I started burning the tiles with a little water and a coarse 6 inch diamond burnishing pad fitted to a hand held rotary machine before moving onto a medium pad. Normally to bring up the polish you would move onto the fine and super-fine pads but it was evident that the other shower walls had a matt finish so there was no need.

Sealing Limestone Shower Tiles

I waited for the Limestone tiles to dry and applied two coats of Tile Doctor Ultra Seal which is a penetrating sealer that will protect the stone from staining.

Damaged Limestone Shower Wall West Hanney After

The owners of the house were very pleased that the wall was not ruined and the cleaning company relieved that the problem had been resolved.
 
 
Source: Professional UK wide maintenance service for Tile, Stone and Grout

Restoring Office Quarry Tiles

A company based in the 17th century market town of Watlington were renovating their office space and decided to replace the carpet which had been glued to the floor below. Upon further inspection this turned out to be a Quarry Tiled Floor and they were keen to restore it and so we got the call.

Quarry Tiles Before Cleaning in Watlington

Restoring Quarry Tiles

I first covered the whole floor with Tile Doctor Remove and Go, leaving this to dwell for a while whilst I fitted a scrubbing pad to my rotary machine. Once the machine was ready the whole floor was scrubbed followed by a rinse with water; the resultant soil was then extracted from the floor using a wet vacuum. This process removed most of the glue so I repeated the process until satisfied all the glue had gone. Remove and Go lives up to its name and although normally used to remove sealers it will remove most other coatings as well. This process took up most of the day so after the final and thorough rinse I left the floor to dry aiming to come back the next day to seal it.

When I returned the next day the floor had white patches of effervescence on it where salts had been forced up through the tile as the water evaporated; this had to be dealt with before the tiles could be sealed so I spent the second day scrubbing the entire floor with Grout Clean Up to remove it, after finishing the floor was given another thorough rinse to remove any product from the floor and used the wet vacuum again to get it as dry as possible.

Sealing a Quarry Tiled floor

I returned the third day to a nice dry and most importantly clean floor. To seal Quarry tiles I usually go for Tile Doctor Seal and Go as it’s water based (so no smell) and it adds a nice shine to the floor; however in this case being an office environment with a lot of heavy traffic I decided to go with Tile Doctor Colour Grow which is an impregnating sealer that soaks into the pores of the tile and is likely to be more durable, it also enhances the natural colours in the tile leading to a very nice finish.

Quarry Tiles After Cleaning in Watlington

I think you will agree the final result was a remarkable transformation
 
 
Source: Office Tiled Floor Restoration in Oxfordshire

Holiday Home Floor Cleaning

This Limestone tiled floor was installed in a holiday rental cottage in Chipping Norton which had a regular change of occupants and was in need of a deep clean and polish. To deep clean stone floors such as Limestone, Marble and Travertine the floor needs to be burnished with diamond encrusted pads.

Limestone Floor Chipping Norton Before

Cleaning Limestone Floor Tiles

The floor was given a quick wash with Tile Doctor Neutral Cleaner in order to remove any surface grit and then cleaned using a set of Burnishing pads fitted to a rotary machine. The burnishing pads come in four different types and you work your way through them starting off with a course stripper pad with a little just water and then carry on with the white pad and then the yellow pad until the floor is thoroughly cleaned and any previous sealer removed. Next step was to use Tile Doctor Pro-Clean along the grout lines with a stiff brush to get the grout cleaner. To bring up the polish on the Limestone tiles I used a polishing pad which is the last in the set of the four burnishing pads. The floor was still wet at this stage so an air dryer machine was used to speed up the drying process.

Sealing Limestone Floor Tiles

Once the floor was dry we set about sealing it using two coats of Tile Doctor Colour Grow which is a colour enhancing sealer designed to provide maximum stain protection on natural stone floors whilst bringing out the deep colour in the stone. The last step was to buff the floor to a nice shine with a rotary machine fitted with a white pad.

Limestone Floor Chipping Norton After
 
 
Source: Limestone holiday cottage floor maintenance in Cambridgeshire